Good day by lukester - March 28th 2024 12:26 pm
| Crazy mods by MufflerMan Mike - March 28th 2024 9:38 am
| | Lew Greger by MufflerMan Mike - March 27th 2024 5:15 pm
| | | How far do I go? | Joined: Mar 2019 Posts: 21 stranger | OP stranger Joined: Mar 2019 Posts: 21 | 77 B200 with 318 and 252K on the clock. Put on 3800 miles since ownership. Uses very little oil, starts ok, runs ok, just don't feel good about taking it anywhere. Pulled it in the shop for the long winter and noticed radiator fins were deteriorating. Long holiday weekend and now I have the whole front end opened up. Radiator, trans cooler, alternator, water pump and fuel pump removed. I couldn't find my compression tester (been thirty years since I used it) so I will run a test next weekend. With the whole winter to go yet where do I stop or should I pull the block and have it rebuilt now. Replace intake and exhaust. Just looking for some thing I can take on a long vacation and not have to be towed home. Thanks | | | Re: How far do I go? | Joined: Feb 2002 Posts: 32,696 Likes: 172 Old Timer | Old Timer Joined: Feb 2002 Posts: 32,696 Likes: 172 | Gone that far I would go all the way!
Jim & Lucy Newkirk 1965 Chevy Bad Influence 1981 Chevy-the Love Shack 2012 Chevy Van , 2020 chevy van 2020 Chevy van Sapphire Sweet. Club Vannerz. vanninvanner@comcast.net | | | Re: How far do I go? | Joined: Mar 2019 Posts: 21 stranger | OP stranger Joined: Mar 2019 Posts: 21 | Yes, thanks for the encouragement. Ceramic headers and new intake? 4 barrel or really go big with new EFI system? I'll see how the compression test works out. Radiator support looks like it's been worked on in the past. Looking for a new one this morning and have not come across one yet. Any sources? Thanks | | | Re: How far do I go? | Joined: Aug 2002 Posts: 18,536 Likes: 135 Supreme Master | Supreme Master Joined: Aug 2002 Posts: 18,536 Likes: 135 | Sounds like you are in pretty deep. Might as well do a full rebuild if you can. Arianrhod:2003 Chevy Astro Black Magic: 1985 Dodge B-250 Serenity:1985 Chevy G-20 The Outcast:1983 Ford club wagon Luna 1974 VW bay window transporter Freedom:1990 Ford E-150(parts van) Outcast Vanners van club Support your local 2% | | | Re: How far do I go? | Joined: Aug 2005 Posts: 21,211 Likes: 25 Supreme Master | Supreme Master Joined: Aug 2005 Posts: 21,211 Likes: 25 | Sounds like you are in pretty deep. Might as well do a full rebuild if you can. Especially with 252,000 miles!
Nate Breece | | | Re: How far do I go? | Joined: Feb 2020 Posts: 111 Likes: 7 BANNED | BANNED Joined: Feb 2020 Posts: 111 Likes: 7 | Especially with a small block, it's easy in and easy out. Sure you'll have a couple grand in it by the time you're done but it's a lot less hassle than getting a tow truck to drag you home after something finally lets loose. Take a picture of the slop in the timing chain. The factory nylon gears were quite but the wore really fast after that 80,000 mile mark. | | | Re: How far do I go? | Joined: Mar 2019 Posts: 21 stranger | OP stranger Joined: Mar 2019 Posts: 21 | Block is out, have a lead for a 75 360 out of a pickup. Would I be better off rebuilding the 318 or the 360? Will the 360 bolt up to my 727 tranny?
Thanks for the help | | | Re: How far do I go? | Joined: Aug 2005 Posts: 21,211 Likes: 25 Supreme Master | Supreme Master Joined: Aug 2005 Posts: 21,211 Likes: 25 | The 360 will "bolt up" but you will need a 360 torque converter because the 318 is internally balanced and the 360 is externally balanced. Also the passenger side mount is different on the 360....not sure if p/u mounts are the same as van mounts to be honest.
If it were me I'd stick with rebuilding the 318. Great little engines.
Nate Breece | | | Re: How far do I go? | Joined: Mar 2019 Posts: 21 stranger | OP stranger Joined: Mar 2019 Posts: 21 | Ok, finally got to drop the 360 block off at the local builder. Race engines stacked everywhere. These guys have been busy over the winter. Builder told me to use a different flex plate(looks like a full circle with a bite out of it) and use a 318 high stall torque converter(2500-3000 rpm's)because they are easier to find then the 360 torque converter. Anybody go this route with success? Thanks | | |
0 members (),
24
guests, and
6
robots. | Key: Admin,
Global Mod,
Mod | | Forums68 Topics35,746 Posts537,916 Members12,724 | Most Online177 May 8th, 2013 | | | |