Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
1991 G20 Rockwood
by frscke1. September 20th 2019 6:41 pm
88 G20 slow resurrection
by frscke1. September 20th 2019 4:37 pm
1978-1982 chevy van parting out
by gasaxechopshop. September 20th 2019 2:13 pm
mid dodge rear door question
by mccarlk. September 20th 2019 7:29 am
new to vannin' in NW Louisiana
by frscke1. September 19th 2019 8:47 pm
Newbie in NW Louisiana
by Telecastorbob. September 19th 2019 7:12 pm
Mlarky's 92 Dodge maybe getting new drive train soon.
by Reed. September 19th 2019 12:11 pm
blown head gasket :eek:
by shaggy. September 19th 2019 8:59 am
Replacing round headlights for rectangle 81 Chevy Van
by NEmery. September 18th 2019 11:19 am
Tuner4life's 1985 Chevy G20 4 Speed Build Thread
by tuner4life. September 18th 2019 7:58 am
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
78 G30 Pathfinder conversion stuffed into a 92 G30 EWB #749443
June 11th 2019 3:03 am
June 11th 2019 3:03 am
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
H
Hairoinn Offline OP
stranger
Hairoinn  Offline OP
stranger
H
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
Started this in the new member section... current status on my build is rear end installed. New bushings. Front end in place. Also new bushings. Half welded. Complete 402 BBC was dropped in my lap last week. Current 350 is ready to be removed. Held in place by a chain wrapped around motor and a piece of angle iron sitting on jack stands in the floorboards. Steering and front brakes are not hooked up. 4 bolts will remove front axle. Lift front end of van off of front axle and roll it out. Drop it to the ground. Jack up motor and disconnect the chain. Lift van up and off of 350/4l80. Drag it out of the way. Support for safety. Finish welding. Assemble new motor, tranny, transfer case. Slide it under van and set body over it. Lift it some and chain it up. Reverse the process.....
More pix to come.

Attached Files 20190508_172427.jpg20190514_142536.jpg

85 Chevy SWB G20 292 w/ 3 on the tree (had it in high school)
78 Chevy SWB G30 350 700r4 Pathfinder 4x4 conversion (wrecked in 08)
92 Chevy EWB G30 350 4l80e (bought with 587k miles for the body. Getting transplants from wrecked 78. Then big block)
Various minis over the years.
Re: 78 G30 Pathfinder conversion stuffed into a 93 G30 EWB [Re: Hairoinn] #749559
June 12th 2019 8:03 am
June 12th 2019 8:03 am
Joined: May 2019
Posts: 52
Kennesaw
M
MXDUDE Offline
journeyman
MXDUDE  Offline
journeyman
M
Joined: May 2019
Posts: 52
Kennesaw
That is going to be sweet! Keep us updated! Out of curiosity, what tranny are you going with? Why not the 4L80?

Re: 78 G30 Pathfinder conversion stuffed into a 93 G30 EWB [Re: MXDUDE] #749604
June 12th 2019 9:31 pm
June 12th 2019 9:31 pm
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
H
Hairoinn Offline OP
stranger
Hairoinn  Offline OP
stranger
H
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
The 700r4 tailshaft adapter to mount a ford np205 is already on. (Proprietary pathfinder equipment company part) came from the one I wrecked. Adapter for a 4l80 is around 700 bucks. Maybe when I'm richer...

Attached Files 20181024_165020.jpg

85 Chevy SWB G20 292 w/ 3 on the tree (had it in high school)
78 Chevy SWB G30 350 700r4 Pathfinder 4x4 conversion (wrecked in 08)
92 Chevy EWB G30 350 4l80e (bought with 587k miles for the body. Getting transplants from wrecked 78. Then big block)
Various minis over the years.
Re: 78 G30 Pathfinder conversion stuffed into a 93 G30 EWB [Re: Hairoinn] #750021
June 26th 2019 5:45 am
June 26th 2019 5:45 am
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
H
Hairoinn Offline OP
stranger
Hairoinn  Offline OP
stranger
H
Joined: Dec 2018
Posts: 24
Flagstaff, AZ
Friday's project was to mount the tail end of the tranny. This is the before picture. I'll get the after picture next time... had to cut the pathfinder equipment company bracket and move the tabs some. Added 2 plates to weld the body brace to. The brace on a 92 EWB is apparently in a different spot than it is on a 78 SWB. Mounted ,tightened, cut, jacked, measured, tacked, measured again, welded. It is in and solid. I'll add another piece of angle iron to the front edge to box it in later.

Attached Files 20190614_175705.jpg

85 Chevy SWB G20 292 w/ 3 on the tree (had it in high school)
78 Chevy SWB G30 350 700r4 Pathfinder 4x4 conversion (wrecked in 08)
92 Chevy EWB G30 350 4l80e (bought with 587k miles for the body. Getting transplants from wrecked 78. Then big block)
Various minis over the years.

Moderated by  Astro 

Donate


Upcoming Events
discovery
Who's Online Now
0 registered members (), 2 guests, and 4 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Telecastorbob, brokevanlife, Speedpower, sinner, dodgedan78
11135 Registered Users
Top Posters(30 Days)
Reed 49
frscke1 45
Forum Statistics
Forums68
Topics36,330
Posts523,821
Members11,135
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1