Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
Dodge vans in movies
by newkirkinc1. October 22nd 2019 6:47 am
Hello from Tennessee
by Gnarlyfoot. October 22nd 2019 12:25 am
EMERGENCY HELP NEEDED NEAR BUTTONWILLOW, CA
by Reed. October 21st 2019 10:10 pm
Old club
by newkirkinc1. October 21st 2019 8:39 pm
Midwest body shop recommendation needed
by newkirkinc1. October 21st 2019 7:52 pm
bumper: repair, replace, or leave it
by textual. October 21st 2019 5:17 pm
Converting my G20 to RHD and 4x4
by Overdrive915. October 21st 2019 4:32 am
1985 Dodge B150 fails emissions twice!
by Reed. October 20th 2019 10:21 pm
The Pilgrimage Campout 2 - October 18-20 2019, 29 Palms CA
by newkirkinc1. October 20th 2019 8:57 pm
Van Names
by newkirkinc1. October 20th 2019 8:51 pm
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
Sticking Advance Weights #747259
April 11th 2019 6:16 pm
April 11th 2019 6:16 pm
Joined: Mar 2019
Posts: 3
Charlotte,NC, USA
T
TommyBoombotz Offline OP
stranger
TommyBoombotz  Offline OP
stranger
T
Joined: Mar 2019
Posts: 3
Charlotte,NC, USA


Can anyone tell me if this is normal or not? Im thinking its not, LOL. Trying to make something of this $400 86 G20, and as im going through the basics, I came across this.

Thanks

Botz

Re: Sticking Advance Weights [Re: TommyBoombotz] #747270
April 12th 2019 12:22 am
April 12th 2019 12:22 am
Joined: Aug 2001
Posts: 12,035
Fircrest, WA
Reed Offline
Maniac
Reed  Offline
Maniac
Joined: Aug 2001
Posts: 12,035
Fircrest, WA
That is not normal at all. The good news is that you should be able to disasemble, clean, and lubricate them to work properly. Heck, just spraying them with some WD-40 or Knock 'Er Loose might do the trick.


Windows- they're what make a van worth owning!
Re: Sticking Advance Weights [Re: TommyBoombotz] #747293
April 12th 2019 7:07 pm
April 12th 2019 7:07 pm
Joined: Nov 2013
Posts: 3,459
Michigan
Dyno_Dave Offline
pooh-bah
Dyno_Dave  Offline
pooh-bah
Joined: Nov 2013
Posts: 3,459
Michigan
If lube doesn't get it done, it may need new springs too.

Re: Sticking Advance Weights [Re: TommyBoombotz] #747305
April 13th 2019 10:23 am
April 13th 2019 10:23 am
Joined: Mar 2011
Posts: 348
NY
J
jcd74 Offline
enthusiast
jcd74  Offline
enthusiast
J
Joined: Mar 2011
Posts: 348
NY
The rotor shaft sticks inside the dizzy, it happens. If your up to it, pull the dizzy and take it apart, there's a roll pin at the bottom holding the gear on. You can try without removing the dizzy if you loosen the pick up, pull it up and you will see a felt washer, pull it up and lube it working the shaft back and forth a little till it frees up. Be careful with the pick up wires, they are frail and don't get the lube on the pick up. it is actually regular maintenance to lube it every so many tune ups. The space under the felt is a lube well for it.

Re: Sticking Advance Weights [Re: TommyBoombotz] #747315
April 14th 2019 8:58 am
April 14th 2019 8:58 am
Joined: Mar 2019
Posts: 3
Charlotte,NC, USA
T
TommyBoombotz Offline OP
stranger
TommyBoombotz  Offline OP
stranger
T
Joined: Mar 2019
Posts: 3
Charlotte,NC, USA
Thanks guys! Gonna swap the springs and lube it up today, I'll post results later.

Botz

Re: Sticking Advance Weights [Re: TommyBoombotz] #747320
April 14th 2019 12:31 pm
April 14th 2019 12:31 pm
Joined: Aug 2001
Posts: 12,035
Fircrest, WA
Reed Offline
Maniac
Reed  Offline
Maniac
Joined: Aug 2001
Posts: 12,035
Fircrest, WA
Try and get identical springs. Don't just throw any old springs on there. THose springs play a very large rolein your timing advance curve and putting in different springs will change your timing advance. If you don't know how to fine tune your advance curve, try clenaing everything and relubing before you replace the springs.


Windows- they're what make a van worth owning!
Re: Sticking Advance Weights [Re: TommyBoombotz] #747324
April 14th 2019 5:12 pm
April 14th 2019 5:12 pm
Joined: Jun 2010
Posts: 1,032
USA
N
nikothenomad Offline
old hand
nikothenomad  Offline
old hand
N
Joined: Jun 2010
Posts: 1,032
USA
Ours were like that until we cleaned them up and lubed everything. Check it out here.... http://nikothenomad.blogspot.com/2015/03/the-healing-of-annie.html

now I could spin the shaft in my hand and they fly out smooth and easy as expected.


Nicole
1988 Dodge B250 5.9l 360 Ram CamperVan / 727 Tranny / Rochester Quadrajet Carb
www.nikothenomad.blogspot.com

Moderated by  Astro 

Donate


Upcoming Events
discovery
Who's Online Now
0 registered members (), 1 guest and 3 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Turboscotty, handymanvan, Nickb, MadMax69, Bargo
11190 Registered Users
Top Posters(30 Days)
frscke1 58
Reed 41
Wedgy 28
Eden 17
Forum Statistics
Forums68
Topics36,472
Posts524,688
Members11,190
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1