Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
Looking to Restore this Shorty!
by brigrat. October 17th 2019 9:32 pm
The Pilgrimage Campout 2 - October 18-20 2019, 29 Palms CA
by samhain. October 17th 2019 8:29 pm
Converting my G20 to RHD and 4x4
by frscke1. October 17th 2019 6:48 pm
Hi
by newkirkinc1. October 17th 2019 12:36 pm
Jeff Dunham is one of us!!!
by Pokin'Panel. October 17th 2019 12:35 pm
Phil de France - Normandie - Caen
by Gnarlyfoot. October 16th 2019 10:09 pm
Interchangeable parts?
by Scrojira. October 16th 2019 9:58 pm
1985 Dodge B150 fails emissions twice!
by Reed. October 16th 2019 9:21 pm
WTB Shorty - in the NYC Area
by 77shortie. October 16th 2019 5:27 pm
G20/Vandura - How to find parts?
by Highlove. October 16th 2019 5:19 pm
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Installed new door seals, can’t get side swing out doors adjusted properly #745449
February 19th 2019 7:15 pm
February 19th 2019 7:15 pm
Joined: Dec 2017
Posts: 25
Ontario, Canada
amcochrane Offline OP
newbie
amcochrane  Offline OP
newbie
Joined: Dec 2017
Posts: 25
Ontario, Canada
Hey guys and gals,

I’ve got an 86 g20 and decided to replace the torn up seals on the swing out side doors as well as the rear cargo doors.

I started with the side doors and the seals clipped in without a problem. As soon as I tried to close the doors I noticed they are now WAY out of adjustment(no issues before replacement). I’m at my wits end loosening and tightening the hinge bolts to get them right. Does anyone have any experience with this or any tips/tricks?

Greatly appreciated,
Aaron

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745450
February 19th 2019 8:02 pm
February 19th 2019 8:02 pm
Joined: Jan 2001
Posts: 2,241
East Brady, PA
M
Meanmachine Offline
veteran
Meanmachine  Offline
veteran
M
Joined: Jan 2001
Posts: 2,241
East Brady, PA
When you say "out of adjustment", do you mean the doors won't close completely shut. Anytime I installed new weatherstrip, I had to let the doors half latched for a few days till the rubber compressed. Installing new weatherstrip should not of changed the hinge adjustment or alignment on the doors. Be careful trying to close them. I have seen doors bent or buckle because guys were using to much force to try to close them. Also sometimes the new weatherstrip is a thicker bulb than the original.

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: Meanmachine] #745451
February 19th 2019 8:07 pm
February 19th 2019 8:07 pm
Joined: Dec 2017
Posts: 25
Ontario, Canada
amcochrane Offline OP
newbie
amcochrane  Offline OP
newbie
Joined: Dec 2017
Posts: 25
Ontario, Canada
Thanks for the quick reply meanmachine.

It looks to me like the striker side of the “front” side door is about 1/2” away from where it’s supposed to be. I don’t think the seal is touching the “rear” side door at all. I’ll leave the door half shut for a couple days and see what happens.

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745453
February 19th 2019 9:09 pm
February 19th 2019 9:09 pm
Joined: Jan 2001
Posts: 2,241
East Brady, PA
M
Meanmachine Offline
veteran
Meanmachine  Offline
veteran
M
Joined: Jan 2001
Posts: 2,241
East Brady, PA
Hold the old weatherstrip up against the new seals and see how the size or diameter of the rubber compares. That will give you an idea if the thickness is the problem.

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745454
February 19th 2019 9:13 pm
February 19th 2019 9:13 pm
Joined: Sep 2005
Posts: 8,838
Nuya
C
CatFish Offline
carpal tunnel
CatFish  Offline
carpal tunnel
C
Joined: Sep 2005
Posts: 8,838
Nuya
Also, cold weather and new weatherstrip don't get along well together.

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745456
February 20th 2019 12:05 am
February 20th 2019 12:05 am
Joined: Feb 2002
Posts: 483
vanland Des Moines
Lionvan Offline
addict
Lionvan  Offline
addict
Joined: Feb 2002
Posts: 483
vanland Des Moines
I got the same problem. Been almost 2 years and they still won't shut without slamming th s#%@ out of them.Thinking about some stick on or glue on universal from Steele.


[IMG]A foolish faith in authority is the worst enemy of truth. Question Authority.
Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745457
February 20th 2019 1:15 am
February 20th 2019 1:15 am
Joined: Jun 2010
Posts: 14,505
Van Diego California
frscke1 Offline
frscke1  Offline

Joined: Jun 2010
Posts: 14,505
Van Diego California
The Desert did wonders for the set on my '93 .... molded it self nicely ... the seals are thicker.


SUNSHINE VANS-VAN DIEGO
ADRENALIN BY THE GALLON & CHASIN RACIN
ONE FOR THE DIRT & ONE FOR THE STREETS
'93 CHEVY G30 454 4X4 SPORTVAN EXT 146" WB
'92 CHEVY G30 454 BEAUVILLE EXT 146" WB
Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745466
February 20th 2019 10:14 am
February 20th 2019 10:14 am
Joined: Dec 2017
Posts: 25
Ontario, Canada
amcochrane Offline OP
newbie
amcochrane  Offline OP
newbie
Joined: Dec 2017
Posts: 25
Ontario, Canada
I'm going to try (carefully) warming the seals with a heat gun and see if i can shut the door. I'll leave it like that for a couple days and see if that helps.

Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: amcochrane] #745513
February 21st 2019 9:45 am
February 21st 2019 9:45 am
Joined: Sep 2013
Posts: 884
Indiana
tuner4life Offline
old hand
tuner4life  Offline
old hand
Joined: Sep 2013
Posts: 884
Indiana
My 1985 has all new seals on the doors as well and after a year they finally are getting a little easier to close. Unfortunately it's just kind of how it is with the aftermarket seals available today. My "60" door was especially hard to close (and still kind of is). I found that the main issue is the leading edge of the seal. It starts putting pressure against closure when the door is still a few inches from closing. This might be able to be remedied bu adjusting the hinges, but for me panel gaps/fitment > easy closure.


[Linked Image]
Re: Installed new door seals, can’t get side swing out doors adjusted properly [Re: tuner4life] #745516
February 21st 2019 9:57 am
February 21st 2019 9:57 am
Joined: Dec 2017
Posts: 25
Ontario, Canada
amcochrane Offline OP
newbie
amcochrane  Offline OP
newbie
Joined: Dec 2017
Posts: 25
Ontario, Canada
Tuner, that's the exact same issue i'm having. the "40" door is tight but closes pretty good. The "60" door is so bad that i dont think the seal is touching the "40" door at all (where the two meet up). I didnt get a chance to hit the seals with some heat last night but i'm hoping that will help.

Page 1 of 3 1 2 3

Moderated by  Astro 

Donate


Upcoming Events
discovery
Who's Online Now
0 registered members (), 2 guests, and 4 spiders.
Key: Admin, Global Mod, Mod
Newest Members
GRUGVan, ResbeardFL, Brocklanders, vn1500, WingNut
11183 Registered Users
Top Posters(30 Days)
frscke1 59
Reed 38
Wedgy 27
shaggy 19
Forum Statistics
Forums68
Topics36,444
Posts524,583
Members11,183
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1