Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
Good day
by SDMickey - March 27th 2024 10:55 pm
Crazy mods
by frscke1 - March 27th 2024 9:37 pm
Lew Greger
by MufflerMan Mike - March 27th 2024 5:15 pm
1987 G20 Gypsy
by SDMickey - March 25th 2024 9:39 pm
Featured Links


Previous Thread
Next Thread
Print Thread
Rate Thread
choke engine light staying on!
#737854 July 02nd 2018 10:49 pm
Joined: Feb 2018
Posts: 59
J
journeyman
OP Offline
journeyman
J
Joined: Feb 2018
Posts: 59
i replaced the oil pressure switch thinking that was the problem but still staying on. i have 12 volts to the electric choke.

Re: choke engine light staying on!
jgarrett #737855 July 02nd 2018 10:49 pm
Joined: Aug 2001
Posts: 12,107
Likes: 37
Maniac
Offline
Maniac
Joined: Aug 2001
Posts: 12,107
Likes: 37
Make? Model? Year?


Windows- they're what make a van worth owning!
choke engine light staying on!
#737867 July 03rd 2018 2:46 pm
Joined: Feb 2018
Posts: 59
J
journeyman
OP Offline
journeyman
J
Joined: Feb 2018
Posts: 59
1982 Chevy g10 350 5.7

Re: choke engine light staying on!
jgarrett #737889 July 04th 2018 2:30 pm
Joined: Feb 2018
Posts: 59
J
journeyman
OP Offline
journeyman
J
Joined: Feb 2018
Posts: 59
does anyone know where the relay is located?

Re: choke engine light staying on!
jgarrett #737892 July 04th 2018 3:14 pm
Joined: Mar 2011
Posts: 513
Likes: 55
J
addict
Offline
addict
J
Joined: Mar 2011
Posts: 513
Likes: 55
If the choke is not working, then the light comes on. You can have power to the at the choke and if the power does not flow thru the light will come on. Check for a ground tail (little black wire from the choke and repair it, broken connector, not on screw, ect. If you have a test light and the test light bulb is stronger than the bulb in the dash, you may see the choke light go out when you check for power at the choke. If the choke light goes out when you test, check ground and check for continuity across choke leads (hot to ground) If open - bad choke.

Re: choke engine light staying on!
jcd74 #737933 July 05th 2018 5:42 pm
Joined: Feb 2018
Posts: 59
J
journeyman
OP Offline
journeyman
J
Joined: Feb 2018
Posts: 59
its a brand new edelbrock carb with a electric choke so i dont think its bad. I did try something today i unplugged the oil pressure switch and the choke light came off. Its a brand new switch from ac delco i dont think its bad.

Re: choke engine light staying on!
jgarrett #737983 July 06th 2018 7:24 pm
Joined: Mar 2011
Posts: 513
Likes: 55
J
addict
Offline
addict
J
Joined: Mar 2011
Posts: 513
Likes: 55
That's a good thing, There's a good chance there is no short in the wiring. Remember when you unplug the switch, you unplug the power for the choke light. Keep in mind no new part is good until it has proven it's self ! I just gave a quick check on my 84 and the wiring is like this, Power from the choke fuse brown/white goes to the switch, from the switch there are two wires out light blue to the choke and dark blue to the choke light.
With the engine off and the ignition switch in run you should have no power at the choke or the lamp. Unplug the oil switch and you should have power on the brown/white.

If you have power on the brown/white install a jumper on the oil switch connector. You should have power at the choke and lamp.

If the lamp goes out the oil switch is bad. The switch may not close all the way, it may show 12 volts coming out, but it cannot let enough power thru to feed the choke. What little is getting thru can power the lamp because the lamp uses little power. But good news the circuit works and the lamp is telling you there is a problem! Don't remove the jumper for the oil switch yet.

If the lamp is on and you have 12 volts to the choke, the choke is bad or the choke ground is bad.
You can take a wire and ground the choke, just go choke ground or carb mounting stud to clean bare metal part on engine. Did the light go out? fix the ground. The choke relies on a ground path from the intake thru the carb mounting hardware to the carb body. Plastic spacer? Hell, did you spring for the plastic carb body? Did the plastic carb come with a extra ground tail for the choke?

You can do one more check to see if the light goes out, you need to put a bigger load on the choke wire. The easy thing without spending alot of money may be to buy a 1156 lamp and lamp holder, if you wire it to the choke wire and touch the lamp holder to ground, the 1156 lamp should go on and the choke light should go out.
If the choke light does not go out you may have a problem with "bulb test" in the ignition switch.

!!!!!!!!!!!! jgarrett "bulb test" does not apply to you, You stated that "the choke light goes out when you unplug the oil switch" if your choke light stays on with the oil switch off then bulb test would apply to the problem!!!
I did not realize this until I was finished writing it, I am only leaving it for reference for other people with choke problems.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Put everything back the way you found it, remove the jumper ect.
The ignition switch has a bulb test feature in "start or crank". You may have noticed the dash lights up like a Christmas tree when you go to start the engine, this is the "bulb test" feature. There two extra contacts in the ignition switch, one that switches positive and the other switches ground. It's there to check the dash lamps. The one that switches positive may be stuck closed and sending power to the check engine light.

If you look at the top column just above where the column mounts, looking form the right side you will see ignition switch. Bunch of heavy red and pink wires, at the left side of the connector there are two small wires. One is "black" switched ground, the other "tan" switched hot (+positive).

With the ignition switch in "run" and the oil switch unplugged (no jumper!) check for power at the tan wire. You should have no power. If you have power the switch is bad.
If your feeling brave ( I hate cutting up factory wiring, but it will save you the trouble of changing the switch) follow the tan wire down 3 inches or more from the ignition switch and cut it. Leave enough so it's easy to re-splice. If the choke light goes out, change the ignition switch. If you want tape off both side of the tan wire untill you change the switch.


Re: choke engine light staying on!
jgarrett #738040 July 09th 2018 6:49 pm
Joined: Feb 2018
Posts: 59
J
journeyman
OP Offline
journeyman
J
Joined: Feb 2018
Posts: 59
wow this is some awesome info!! sorry havent been back to you yet just got home from a vannin. Im def going to try checking power at the oil pressure switch its got to be a bad switch from factory.


Moderated by  Astro 

Link Copied to Clipboard
Donate


Upcoming Events
discovery
Who's Online Now
0 members (), 13 guests, and 5 robots.
Key: Admin, Global Mod, Mod
Newest Members
TheDrunkenGunsmith, Jac, LOVclassics, ZenMuffin, Milkman530
12724 Registered Users
Top Posters (30 Days)
SDMickey 130
CatFish 28
frscke1 28
Wedgy 20
Forum Statistics
Forums68
Topics35,747
Posts537,897
Members12,724
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.7.4