Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
WILD CHERRY lives !
by CatFish. September 23rd 2018 3:17 pm
Smacked a deer. Now, no high beams.
by frscke1. September 23rd 2018 9:07 am
Vantastic
by frscke1. September 23rd 2018 9:02 am
For those who like a challenge: mysterious blown fuses.
by UncleCreepy. September 23rd 2018 2:02 am
FS: Chevy slider door extender
by frscke1. September 22nd 2018 8:20 pm
My 1991 B-250....again !
by Reed. September 22nd 2018 5:03 pm
Looking for 90mm ID centric rings for my B250? Wheel options?
by fishbone. September 22nd 2018 4:22 pm
Chevy sliding door arm (stock length)
by frscke1. September 22nd 2018 4:22 pm
'82 Dodge Pass. Vent Window Seeking parts or complete
by frscke1. September 22nd 2018 3:44 pm
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
B200 Oil Pan Removal? #737618
June 27th 2018 2:42 am
June 27th 2018 2:42 am
Joined: Mar 2015
Posts: 62
London, UK
B
Bourneavanner Offline OP
journeyman
Bourneavanner  Offline OP
journeyman
B
Joined: Mar 2015
Posts: 62
London, UK
Hey guys,

Does anyone know if there is a way to remove the Oil Pan easily off of a 72' Dodge b200? It looks as though the support beam is going to block me from removing it completely...I would like to avoid having to hoist the engine up to egt it off, so if any of you guys have an info for me on how best to do this it would be greatly appreciated!

Cheers

Bourneavanner
[Linked Image]

Re: B200 Oil Pan Removal? [Re: Bourneavanner] #737671
June 28th 2018 5:17 pm
June 28th 2018 5:17 pm
Joined: Jan 2018
Posts: 18
UK
L
LazySteve Offline
stranger
LazySteve  Offline
stranger
L
Joined: Jan 2018
Posts: 18
UK
I did it on my '73 B300 which I think is pretty much the same sort of deal, or even may be exactly the same.

I guess it all depends on what you call "easily". As far as I can remember I did have to raise the engine but it was just a case of undoing the mounts and jacking it from underneath (I think I had a wooden block on the jack under the front pulley and lifted from the front end). I definitely didn't have to unbolt the transmission.

The main thing that gets in the way of sliding out the pan is the oil pump pickup and you have to sort of feed it around at funny angles, but it does come out (well mine did).

When you put it back together you also have to be careful with how the seals fit around the front end timing cover area as some of them go together at different angles.

I did mine to investigate a bad oil pressure issue which eventually turned out to be just a defective (new) Fram filter !!

I'm in the UK too BTW.

Re: B200 Oil Pan Removal? [Re: Bourneavanner] #737701
June 29th 2018 12:37 pm
June 29th 2018 12:37 pm
Joined: Mar 2016
Posts: 322
Tucson,Az.
H
Hasan Ben Sobar Offline
enthusiast
Hasan Ben Sobar  Offline
enthusiast
H
Joined: Mar 2016
Posts: 322
Tucson,Az.
Fram is garbage. I wouldn't use one on a lawn mower. Wix or NAPA.


Tucson-it's a dry heat...like an oven
Re: B200 Oil Pan Removal? [Re: Hasan Ben Sobar] #737809
July 02nd 2018 3:02 am
July 02nd 2018 3:02 am
Joined: Jan 2018
Posts: 18
UK
L
LazySteve Offline
stranger
LazySteve  Offline
stranger
L
Joined: Jan 2018
Posts: 18
UK
Yeah - my hot idle pressure went from like 5 psi to 20.

Re: B200 Oil Pan Removal? [Re: Bourneavanner] #737912
July 05th 2018 12:48 pm
July 05th 2018 12:48 pm
Joined: Mar 2015
Posts: 62
London, UK
B
Bourneavanner Offline OP
journeyman
Bourneavanner  Offline OP
journeyman
B
Joined: Mar 2015
Posts: 62
London, UK
Hey guys,

Thanks for the info! I'll let you know how I get on, although I can't say I'm excited at having to do all that work just to change the pan gasket!? Ugh!


Moderated by  Astro, nautic1, Ram4ever 

Donate


Upcoming Events
discovery
Instagram Feed
Who's Online Now
1 registered members (bubbafat), 0 guests, and 11 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Vanquish, The_El_Don, NateN, RasKovnik, Icculus
10560 Registered Users
Top Posters(30 Days)
frscke1 110
Reed 65
Dw89xj 46
CatFish 38
Forum Statistics
Forums68
Topics34,630
Posts512,695
Members10,560
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1