Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
Drop spindles question
by DaveyRiot. June 05th 2020 8:27 pm
Help with Vin Number
by Deathorvictory. June 05th 2020 7:01 pm
MVI ?
by Meanmachine. June 05th 2020 6:22 pm
Sharon Richards AKA: "Lady"
by newkirkinc1. June 05th 2020 2:15 pm
Hello from germany
by Astronaut. June 05th 2020 12:28 pm
3rd gen Ford slider extender
by oldskool73. June 05th 2020 12:14 pm
butler 2020
by newkirkinc1. June 05th 2020 9:51 am
Original 1969 Ford E-200 for Sale
by SpaceTruckin. June 04th 2020 7:03 pm
Vintage Gold Vein Mirrors- $3 each
by dragonvanman. June 04th 2020 12:49 pm
Vintage Auto Magazines
by Charlie99909. June 04th 2020 12:21 pm
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
anchoring a subfloor in a van #735040
April 13th 2018 7:38 pm
April 13th 2018 7:38 pm
Joined: Feb 2017
Posts: 32
Atlanta Ga
1
1993chevyg20 Offline OP
newbie
1993chevyg20  Offline OP
newbie
1
Joined: Feb 2017
Posts: 32
Atlanta Ga
anchoring a subfloor in a van

So I pulled up the nasty carpet in my 93 Chevy van. I’m contemplating on what to put down in its place. I plan to start with a plywood subfloor.

Some noise suppression seems ideal. Also, do you anchor the subfloor with sheet metal screws and just hope that you don’t hit something important?

Any suggestions would be appreciated

Thanks

Re: anchoring a subfloor in a van [Re: 1993chevyg20] #735053
April 13th 2018 8:40 pm
April 13th 2018 8:40 pm
Joined: Aug 2005
Posts: 3,697
Wichita Falls, Texas
Starlord Offline
pooh-bah
Starlord  Offline
pooh-bah
Joined: Aug 2005
Posts: 3,697
Wichita Falls, Texas
In the past we've always used sheet metal screws. You MUST crawl around under the van and take note what is in the way and what you don't want to sink a screw into. Some folks in the past have just sunk screws and "vented" their gas tanks or something else that isn't supposed to have a screw in it (a hot wire that suddenly has a ground via a screw and metal floor is very bad news). Some use a insulator on the floor before putting the subfloor in, some don't, if you are carpeting the floor that will provide pretty good sound deadener. Don't use thin plywood for the subfloor, get some thicker stuff. Remember, you don't have to use a ton of screws to put your floor in, just enough to keep it from bouncing up and slamming down on bumps. In addition to sheet metal screws, you can get away with exterior grade deck screws, most will screw in without drilling a hole first.


2005 E350 Turbo Diesel
Why is it that when I press 1 for English, I still can not understand the person on the other end????
Re: anchoring a subfloor in a van [Re: 1993chevyg20] #735127
April 15th 2018 1:43 pm
April 15th 2018 1:43 pm
Joined: Feb 2017
Posts: 32
Atlanta Ga
1
1993chevyg20 Offline OP
newbie
1993chevyg20  Offline OP
newbie
1
Joined: Feb 2017
Posts: 32
Atlanta Ga
Thanks Starlord

I don't think I am going back down with carpet. What are people using for sound dampening? It there something that I can put in between the subfloor and the top flooring? The top flooring will be some fake wood floor that you might put down in the kitchen


Thanks

Re: anchoring a subfloor in a van [Re: 1993chevyg20] #735150
April 16th 2018 8:26 am
April 16th 2018 8:26 am
Joined: Sep 2013
Posts: 974
Indiana
tuner4life Offline
old hand
Happy Birthday tuner4life  Offline
old hand
Joined: Sep 2013
Posts: 974
Indiana
I was considering using "T" bolts through the plywood and using nuts under the floor. Would that not be much more solid of a plan than self-tappers? More serviceable in the future too?


[Linked Image]
Re: anchoring a subfloor in a van [Re: 1993chevyg20] #735152
April 16th 2018 8:50 am
April 16th 2018 8:50 am
Joined: Sep 2005
Posts: 8,956
Hickory Flat, Jawga
CatFish Offline
carpal tunnel
CatFish  Offline
carpal tunnel
Joined: Sep 2005
Posts: 8,956
Hickory Flat, Jawga
I used the cabinets (which are anchored to the wall struts) , the bed (also anchored to the wall) and the front console to hold down the sub-floor. I'm not much for drilling holes anywhere in the exterior body work if I can figure a way to avoid it.... smile
I used those anti-fatigue mats cut into strips and laid in the low tracks of the van floor to give a level surface. Thin (cross-hatch) sub-floor, reflectex and then plywood. Finished with carpet with a strong backing (actually a rug cut to fit) so it would lay flat. We camp in ours a lot so we needed something that was "bare-foot" friendly.
Our storage area under the bed is a finished panel material to make it easy to vacuum and keep clean.
I got pics somewhere.......

Re: anchoring a subfloor in a van [Re: CatFish] #736111
May 08th 2018 3:24 pm
May 08th 2018 3:24 pm
Joined: Feb 2017
Posts: 32
Atlanta Ga
1
1993chevyg20 Offline OP
newbie
1993chevyg20  Offline OP
newbie
1
Joined: Feb 2017
Posts: 32
Atlanta Ga
Thanks guys

Re: anchoring a subfloor in a van [Re: 1993chevyg20] #736127
May 09th 2018 12:52 pm
May 09th 2018 12:52 pm
Joined: Mar 2005
Posts: 137
Po'land, Or
U
Uncle Blaino Offline
member
Uncle Blaino  Offline
member
U
Joined: Mar 2005
Posts: 137
Po'land, Or
When I put a plywood floor in a full sized van I use "stovebolts" (the ones with the rounded head... that stays flush with the top of the plywood) and drill my holes from the bottom. That way I don't have to worry about drilling into the gas tank or brake/gas lines.
a quarter inch bolt is sufficient, but use a big (fender) washer & lock ring on the bottom. You won't have to worry about it pulling out.
I also lay a full sheet of plywood in the middle of the van & then cut to shape pieces to fit the sides. Then I use a little fiberglass cloth to join the three pieces into one piece.
It's been a while, but I think I was able to get buy just using four or five bolts and it was solid.
The wood floor seemed to provide enough insulation for me.

Re: anchoring a subfloor in a van [Re: 1993chevyg20] #736175
May 10th 2018 8:05 pm
May 10th 2018 8:05 pm
Joined: Sep 2005
Posts: 8,956
Hickory Flat, Jawga
CatFish Offline
carpal tunnel
CatFish  Offline
carpal tunnel
Joined: Sep 2005
Posts: 8,956
Hickory Flat, Jawga
On the GMC, the last time I redid it, I cut some fatigue mats into strips for lower portions of the "ribs" in the floor. (just found the pics)

[Linked Image]

Helps to give it a more solid feeling with a lighter weight subfloor.

Last edited by CatFish; May 10th 2018 8:12 pm.

Moderated by  Astro 

Donate


Upcoming Events
Vanfest 2020
06-12-2020
discovery
Who's Online Now
1 registered members (1 invisible), 3 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
Newest Members
computerfix619, Astronaut, SkinnyDingle, Gman28, Looking
11464 Registered Users
Top Posters(30 Days)
SDMickey 300
kursed 69
Lee7673 60
frscke1 47
Forum Statistics
Forums68
Topics37,492
Posts532,465
Members11,465
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1