Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
1991 G20 Rockwood
by 91Chev. September 22nd 2019 7:35 pm
88 G20 slow resurrection
by frscke1. September 22nd 2019 4:17 pm
What Did You do To your Van Today?
by Wedgy. September 22nd 2019 12:16 pm
Bblintpicker's 77 Dodge, "Devil's Way" Street Van
by Wedgy. September 22nd 2019 9:22 am
van photographer
by dix. September 22nd 2019 8:38 am
Converting my G20 to RHD and 4x4
by Overdrive915. September 22nd 2019 6:00 am
TABLES! Share some info pics please.
by shaggy. September 21st 2019 4:07 pm
Newbie in NW Louisiana
by frscke1. September 21st 2019 3:19 pm
Anybody in the Walden/Newburgh/Plat
tkill, NY area??

by BudVanBeer1. September 21st 2019 1:21 pm
MID DODGE
by mccarlk. September 21st 2019 10:15 am
Featured Links
Vanning.Com is a an authorized Amsoil Dealer


Previous Thread
Next Thread
Print Thread
Rate Thread
Fixed steering column #732155
January 22nd 2018 4:12 pm
January 22nd 2018 4:12 pm
Joined: Jan 2018
Posts: 25
CA
M
Miyagi Offline OP
newbie
Miyagi  Offline OP
newbie
M
Joined: Jan 2018
Posts: 25
CA
Dinking with some wires in my 74 tradesman steering column, I'd like to be able to remove the column harness, but can't get past the upper bearing....

In my 80 RV, the ignition switch is in the column, so it's just some screws after pulling the steering wheel to get to the harness... The the shift lever part becomes accessible.
Examples here--https://www.allpar.com/trucks/dodge/steering-column-fix.html

In the tradesman, the ignition switch is in the dash, not the column, so instead of screws beneath the turn signal and hazard wiring, I *thought* it was nuts on studs instead of screws, so I removed the nuts. Turns out they were on bolts, which fell into the shifter space.
The top segment where the signal Cam and hazard switch sit are slightly loosened, but not apparently removable due to a pressed bearing in the way.

At this point, I MUST proceed to restore those bolts into position, but can't.

Re: Fixed steering column [Re: Miyagi] #732158
January 22nd 2018 4:48 pm
January 22nd 2018 4:48 pm
Joined: Jun 2010
Posts: 14,450
Van Diego California
frscke1 Offline
frscke1  Offline

Joined: Jun 2010
Posts: 14,450
Van Diego California
Welcome to the site Miyagi ...


SUNSHINE VANS-VAN DIEGO
ADRENALIN BY THE GALLON & CHASIN RACIN
ONE FOR THE DIRT & ONE FOR THE STREETS
'93 CHEVY G30 454 4X4 SPORTVAN EXT 146" WB
'92 CHEVY G30 454 BEAUVILLE EXT 146" WB
Re: Fixed steering column [Re: Miyagi] #732171
January 22nd 2018 8:51 pm
January 22nd 2018 8:51 pm
Joined: Jan 2018
Posts: 70
Vansfield, USA
Sparkynm Offline
journeyman
Sparkynm  Offline
journeyman
Joined: Jan 2018
Posts: 70
Vansfield, USA
Are you changing the turn signal switch? Once the wheel is off, you need to un-screw the t/s lever, than there are three(3) retaining screws, and plate, that hold the switch in place.
All of the wires, except shift indicator light, are attached to the switch, These run through the shift collar into a screw on cover on top of the column which in turn goes THRU the support bracket for the column itself where there is a connector, which is fairly easy to get your hands on. The problem is the connector will NOT go thru the bracket. You MUST remove the terminals from the connector to pull the whole switch/wire assembly up thru the shift collar. MAKE A DIAGRAM IF YOU DO THIS. ALSO NOTE THE DIRECTION OF THE TERMINALS IN THE CONNECTOR ITSELF. These terminals are TRICKY to get out of the connector. I used dental picks, because had no terminal tool. I changed the whole switch on 72 B200, so I cut off the old connector(see above note), pulled wires thru shift collar, along with switch, Install new switch(wires fed thru easily), down column and THRU the support bracket , Make sure the wires are Thru the bracket before you insert the new wires in the old connector, or it looks kinda bad !! Hope this helps

Re: Fixed steering column [Re: Miyagi] #732173
January 22nd 2018 9:40 pm
January 22nd 2018 9:40 pm
Joined: Jan 2018
Posts: 70
Vansfield, USA
Sparkynm Offline
journeyman
Sparkynm  Offline
journeyman
Joined: Jan 2018
Posts: 70
Vansfield, USA
Sorry after I re-read this, my 2 cents aren't worth too much at this point. Can you get to the snap ring under the switch? May be able to pull up the housing from tube? Service manual shows that the bolts fit into square hole on the back of the bearing housing. Don't know if you have room or not, haven't had one apart that far.
It may be time to pull the column out of the van to fix. Done this one also, not too bad of a job, mine had 3 large phillips screws holding the plate down to the floor along with 2 bolts on upper plate, column support bracket, the roll pin and shift linkage rod. Get yourself the BEST #4 PHILLIPS you can, they are a bear.
If you need , I could take pictures of the manual and post them here, just let me know!! Good Luck


Moderated by  Astro, nautic1, Ram4ever 

Donate


Upcoming Events
discovery
Who's Online Now
2 registered members (Lee7673, 1 invisible), 1 guest and 2 spiders.
Key: Admin, Global Mod, Mod
Newest Members
stampsicle, Primate5er, gphinney, Deagle2008, Telecastorbob
11139 Registered Users
Top Posters(30 Days)
Reed 46
frscke1 46
CatFish 15
Forum Statistics
Forums68
Topics36,333
Posts523,847
Members11,140
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.6.1.1