Vanning.com logo
Boxdin
Site Navigation


Advertisements
Recent Posts
Good day
by lukester - March 28th 2024 12:26 pm
Crazy mods
by MufflerMan Mike - March 28th 2024 9:38 am
Lew Greger
by MufflerMan Mike - March 27th 2024 5:15 pm
1987 G20 Gypsy
by SDMickey - March 25th 2024 9:39 pm
Featured Links


Previous Thread
Next Thread
Print Thread
Rate Thread
Machine Shops
#730555 December 10th 2017 12:33 pm
Joined: Dec 2017
Posts: 30
Likes: 2
7
newbie
OP Offline
newbie
7
Joined: Dec 2017
Posts: 30
Likes: 2
There may be a post about this already, but I can not find it. Do you have a favorite machine shop? I am in need of a shop here in Arizona that does good work with decent prices and good customer service. I need to take a block in to get checked over for cracks and any damage, and possibly bored out if it needs it. I will also need to get the cylinder heads rebuilt at a later time as well. I am between Phoenix and Tucson, so I can go in either direction for a good machine shop. Any recommendations would be greatly appreciated. Maybe we can get a list going for every state?

AdSense long
Re: Machine Shops
74AzMaxi #731547 January 05th 2018 9:10 pm
Joined: Jun 2016
Posts: 69
J
journeyman
Offline
journeyman
J
Joined: Jun 2016
Posts: 69
What engine is it?


JNPerformance.com
Pathfindervans.com
Re: Machine Shops
74AzMaxi #731548 January 05th 2018 9:30 pm
Joined: Mar 2011
Posts: 513
Likes: 55
J
addict
Offline
addict
J
Joined: Mar 2011
Posts: 513
Likes: 55
Don't waste your time rebuilding old heads, unless your are hell bent on keeping your originals you can do better with new one's with no heart ache down the line (cracked heads). You don't have to spring for some race head on a street motor. What motor?

Re: Machine Shops
74AzMaxi #731572 January 06th 2018 10:59 pm
Joined: Mar 2016
Posts: 339
H
enthusiast
Offline
enthusiast
H
Joined: Mar 2016
Posts: 339
Machine Works on Stone in Tucson. Best head guy in town. Nothing wrong with rebuilding LA heads. The later 5.2 and 5.9 motors are the ones with head cracking issues.

Last edited by Hasan Ben Sobar; January 06th 2018 11:01 pm.

Tucson-it's a dry heat...like an oven
Re: Machine Shops
74AzMaxi #732462 January 29th 2018 1:01 am
Joined: Dec 2017
Posts: 30
Likes: 2
7
newbie
OP Offline
newbie
7
Joined: Dec 2017
Posts: 30
Likes: 2
Sorry everyone, I forgot to keep a check on this post. My van is a 1974 Dodge Tradesman 200 Maxi Van. According to the vin number decoder the engine is an "E - LA 318-1 V8 2V". I do have a set of dodge heads in my work shop but not sure what they are from, and I also have an engine from my 1980 dodge w150 which is also a 318 2-bbl engine. So hopefully from the 3 sets of heads I should have one set that is good.Thanks for the responses everyone.

Re: Machine Shops
74AzMaxi #732472 January 29th 2018 12:01 pm
Joined: Mar 2016
Posts: 339
H
enthusiast
Offline
enthusiast
H
Joined: Mar 2016
Posts: 339
I forget how MOPAR changes their CR. If they do it with different CC sizes (heads), you'll want to use the heads that give you the optimum CR. Which will be around 8.5-8.75 to 1. Better a tad low than high as you can play games with cam timing to get more power but if it's too high-you're screwed.

EDIT: Very few differences in CC volume.They used piston height to change CR's. So use the best set of heads you have and mill them to get around 8.75 to 9-ish to 1 CR. If you're going to change the bumpstick, you pick it based on final CR numbers.

Last edited by Hasan Ben Sobar; January 29th 2018 4:35 pm.

Tucson-it's a dry heat...like an oven
Re: Machine Shops
74AzMaxi #732477 January 29th 2018 2:37 pm
Joined: Aug 2001
Posts: 12,107
Likes: 37
Maniac
Offline
Maniac
Joined: Aug 2001
Posts: 12,107
Likes: 37
For the LA series smallblocks, Mopar changed the compresison ratio mostly with combustion chamber size and design, but a little with piston height. In my opinion, the most desireable stock Mopar smallblock heads are the late 80s/early 90s swirl port closed chamber heads (302 casting for 318s, 308 for 360s). These heads have a closed chamber small volume combustion chamber with swirl port design. Dyno tests have shown a 25 hp gain just by bolting on a stock set of these heads. I have a set of the 302 heds I am going to install on the 318 in my 82 Ramcharger.

You can mill the heads or deck the block to increase compression, but too much milling and/or decking requires modification to the intake manifold and valve train. The easier way to increase compression (outside of switching to a head with a smaller combustion chamber) is to use different pistons with a wrist pin farther away from the crown of the piston.

But if all you are wanting to deal with is a head swap, the late 80s/90s swirl port heads are the best LA head design done by Chrysler. As Hasan Ben Sober noted, these heads have a reputation for crackign, so it is best to either buy a rebuilt pair or at least have the ones you want to use checked out. But it is often just as expensive to rebuild a set of heads as it is to buy a new set of rebuilt heads, so unless you are doing custom porting work on a race motor, you should definitely shop around and research the cost of rebuilding what you have vs. buying new.

Good info here: http://www.hotrod.com/articles/mopp-0607-mopar-cylinder-head/


Windows- they're what make a van worth owning!

Moderated by  Astro, nautic1 

Link Copied to Clipboard
Donate


Upcoming Events
discovery
Who's Online Now
1 members (Meanmachine), 21 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Newest Members
TheDrunkenGunsmith, Jac, LOVclassics, ZenMuffin, Milkman530
12724 Registered Users
Top Posters (30 Days)
SDMickey 125
CatFish 25
frscke1 25
Wedgy 21
Forum Statistics
Forums68
Topics35,746
Posts537,916
Members12,725
Most Online177
May 8th, 2013

Powered by UBB.threads™ PHP Forum Software 7.7.4