|
Good day by MufflerMan Mike - March 28th 2024 10:51 am
| Crazy mods by MufflerMan Mike - March 28th 2024 9:38 am
| | Lew Greger by MufflerMan Mike - March 27th 2024 5:15 pm
| | | Transmission Help | Joined: Jan 2012 Posts: 12 stranger | OP stranger Joined: Jan 2012 Posts: 12 | I have a 1994 B250 with a 36rh transmission. Jegs has a rebuilt a727 transmisson for @ 950 bucks and I was wondering if it would work. It looks like mine, but it says a727 1967 to 1979 small block. I was wondering if there is any difference after 1979 that would not work. I feel confident that it would bolt right up, but will my TC work and will my drivehaft have the same splines?
Really want to get my old van back on the road.
Thanks for any help and or advice.
Taking it to the local tranny shop for a rebuild is out. I just had it rebuild 2.5 years ago and 12,000 miles later it won't budge. | | | Re: Transmission Help | Joined: May 2016 Posts: 15 stranger | stranger Joined: May 2016 Posts: 15 | Sounds like you picked the wrong shop the first time! The biggest problem is all the electronics. The older trannys didn't have all the fancy electronics like your newer transmissions do. Find a better shop, or a used one with a warranty.
Vannin' for Life! Irish_Lucky
| | | Re: Transmission Help | Joined: Aug 2001 Posts: 12,107 Likes: 37 Maniac | Maniac Joined: Aug 2001 Posts: 12,107 Likes: 37 | If your Dodge truly has a 36rh (three speed hydraulic controlled automatic) and not a 46rH (four speed hydraulic controlled automatic) or a 46RE (four speed electronic controlled automatic), then the 727 will swap right in. Driveshaft will be the same, but you probably have a lockup torque converter so any replacement trans will have to also be a lockup trans or the torque converter won't work.
Are you sure your van truly has a hydraulic controlled three speed and not an electronic controlled four speed? By 94 almost everything had gone to four speed electronic control.
Windows- they're what make a van worth owning! | | | Re: Transmission Help | Joined: Feb 2007 Posts: 194 member | member Joined: Feb 2007 Posts: 194 | the 36rh is just a renamed 727 after 1989 with a lockup torque converter. If you find an earlyer727 with lockup make sure to get the right converter to match the year of the trany.
Political correctness is a doctrine fostered by a delusional, illogical minority, and rapidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by a CLEAN end. | | | Re: Transmission Help | Joined: Jan 2012 Posts: 12 stranger | OP stranger Joined: Jan 2012 Posts: 12 | Reed,
Thanks for the info. I actually have two 94 Dodge B250. The one is question came from the dealership with a towing package including auxiliary tranny cooler and brake controller, so I am assuming this is why it has the 36rh. My other 94 has the 46rh. The one with the 46rh gets much, much better gas mileage.
Okay Reed just a few more questions if you do not mind. From what I am seeing here is that all 36rh's have a lock up TC. I would assume mine would not be an exception. Anyway is there anyway I can tell if its lock up. There is absolutely no button to mash anywhere on the inside for lockup. Seems to me if it was lock up there would be a button to push to enable the lock up or cut it off. I swear there is not one anywhere. Do you know how I can tell looking at the tranny? I have it out and can send any pics needed.
Thanks again
PJ
Last edited by iamthepreston; April 30th 2017 1:10 am. Reason: Partially Illiterate
| | | Re: Transmission Help | Joined: Aug 2001 Posts: 12,107 Likes: 37 Maniac | Maniac Joined: Aug 2001 Posts: 12,107 Likes: 37 | A-727 transmissions from their inception until 1966 have 19 splines on the input shaft. Non-lockup 727 transmissions from 1967 onward have 24 splines. Lockup 727 transmissions that debuted in 1978 had 23 splines.
Not all 727 transmissions made after 1978 were lockup; towing package 727 transmissions commonly were non-lockup, and would have the ’67-onward 24 spline input shaft. The A-518 overdrive also has 23 splines. The output shaft has 29 splines.
A-904 transmissions from their inception until 1967 have 18 splines in the input shaft. Non-lockup transmissions from 1968 have 27 splines.
Lockup 904 transmissions appeared in 1978, and have 26 splines. A-500 overdrive transmissions also have 26 splines. The output shaft has 25 splines.
If in doubt, count the splines. It saves a lot of headache and stress later on when you might otherwise discover that you have the wrong torque converter or drive shaft yoke." Taken from: http://www.allpar.com/mopar/transmissions/identifying-torqueflites.htmlIn other words, pull the torque converter and count your splines. If the van has a heavy duty towing package, chances are it will have 24 splines. Alternatively, what does the underhood sticker say? It is on the hood above the battery and lists all the options. The button on the dash is for overdrive on the four speed automatics. The lockup feature is controlled hydraulically on older transmissions and electronically by the computer on newer transmissions. No user input is possible to control the lockup of the torque converter.
Last edited by Reed; April 30th 2017 12:18 pm.
Windows- they're what make a van worth owning! | | |
1 members (black79gmc),
18
guests, and
6
robots. | Key: Admin,
Global Mod,
Mod | | Forums68 Topics35,747 Posts537,917 Members12,724 | Most Online177 May 8th, 2013 | | | |
|