Boxdin logo
We host with and recommend Your-Site.Com - This site works best with FireFox - this site is powered by UBBCentral

Site Navigation

Recent Posts
Chronicles of a 79 Dodge
by Reed
22 minutes 56 seconds ago
Summer Crush Gettin Some Paint
by 86ed
Today at 01:18 AM
new kid from the Netherlands!
by 86ed
Today at 01:15 AM
"CARVAN" 1987 B150 Ram Tuff Chevy Stuff.....
by 86ed
Today at 01:10 AM
Scooped Dodge
by 86ed
Today at 12:58 AM
Best Carb Option for my 77 250 inline 6?
by jaysomethin
Today at 12:32 AM
Thinking about buying this van, any input?
by galaxie
Today at 12:23 AM
Hello from Ontario, Canada
by Clyde
Yesterday at 09:39 PM
Aluminium heads--- my head is spinning.,.
by keech
Yesterday at 08:06 PM
Looking to buy Astro or Safari
by pauldeere
Yesterday at 07:00 PM
Featured Links

Cluster Map
Locations of visitors to this page
Topic Options
Rate This Topic
#570893 - June 26th 2012 4:56 am pinion seal replacement
rockinvan Offline

Registered: February 18th 2012 3:12 pm
Posts: 21
Loc: new york us
I need to replace my pinion seal . Is there specs i need to make so I do not ruin the rear end gears ?Thanks

#570898 - June 26th 2012 7:17 am Re: pinion seal replacement [Re: rockinvan]
Happy Birthday Doc 2% of Canada, EH!!!! Offline

Registered: June 10th 2003 12:00 pm
Posts: 12712
Loc: Burlington, On, Canada Eh !!!!
Well , when you re torque the pinion nut its usually around 200 PSI. Check the manual..When I did mine changed the bearings and all the seals, check for clearance etc....then I used synthetic lube in it....
I don't need to be honoured by Vanning, I am honoured to be Vanning !
Supporting Vanning, by going Vanning In A Van !
I hate it, when real life interferes with Vanning !
Van Clan Plus One, Vanning since 1977 !
Ontario Federation Of Truckers (Vanner's)
Ottawa Valley Vans
Founder,Mixed Bag Truckers

#570945 - June 26th 2012 10:16 am Re: pinion seal replacement [Re: rockinvan]
NateNCBV Offline


Registered: August 23rd 2005 12:00 pm
Posts: 20415
Loc: Brooklyn Park, Maryland, USA
Depends on make/model of van you're working on. The factory service manual will have the proper specs.

Ebay is a good place to get a manual.
Nate Breece
North Chesapeake Bay Vans
1994 Dodge B250 Elk Conversion (5.2L/A518)
2008 Dodge Caravan (3.8L)

#571025 - June 26th 2012 5:15 pm Re: pinion seal replacement [Re: rockinvan]
rockinvan Offline

Registered: February 18th 2012 3:12 pm
Posts: 21
Loc: new york us
Thank you

#574638 - July 18th 2012 9:57 am Re: pinion seal replacement [Re: rockinvan]
Alikazam Offline
old hand

Registered: September 14th 2009 8:07 pm
Posts: 852
Loc: Oregon, USA
torque specs in psi? Is that supposed to be ft-lbs? smile Check your service manual for proper specs. Go with facts!!! smile
1972 Dodge Van "Tigerlilly" - Blazing Copper/Sandstone Metallic - 3850 lbs empty
13.47 @ 97.53 mph N/A - 11.94 @ 113.33 mph N2O - old 360/727 + Nitrous (N2O)combo
Viper V10 + 4L80E conversion in progress...

2009 Dodge Challenger SRT8 "Leelu" - TorRed - 6.1L Hemi/6 speed - Vortech V3 8psi - 500+ whp - 4250 lbs empty
12.258 @ 113 mph - best so far & 23+ mpg on the freeway

#574761 - July 18th 2012 8:18 pm Re: pinion seal replacement [Re: rockinvan]
Phoenix Offline

Registered: September 13th 2008 4:42 pm
Posts: 3391
Loc: Evansville, Indiana
I replaced mine with some advise from My friend at my dealership who is the foreman of the service dept.. 250 ft lbs is the torque BUT get it up in the air and with an inch lb torque wrench, step it up with adapters to the nut size and starting at zero with the drive shaft removed put the socket on the yoke nut and turn it. step it up one inch lb. at a time until your rear wheels start to turn. Mine was around eight or ten inch lbs. I think but don't hold me to it. just use your measurement as your standard and write it down. Then go ahead and bust your nut off...LOL I had my C&C dept burn me a rectangle out of steel and welded a handle on it that I used to brace against the frame to break the nut loose and tighten it afterwards. after you get the nut off clean the area up so no dirt gets where you dont want it. get that seal out any way you can ( i used a screw driver and pried it out until I got hold of it then just got it out fairly easy.) Then I used some sealer Permatex copper and put a thin layer on the new seal and with a large socket drove it home. Then put the piece I welded back on the yoke and with my torque wrench put the nut back at 250 ft lbs and it took all I had hanging almost upside down and pushing with my feet on the floor board and finally the torque wrench poped and I checked the torque with my inch lb torque wrench and my wheels started turning at the exact inch lb torque that I started with So I knew I had it right. Just do a start test install the new part and a final test to make sure your pinion load is the same and your done. I hope this helps.
You are welcome to PM me for any questions you have or a pic of the piece I made for a counter wrench.

Edited by Phoenix (July 18th 2012 8:19 pm)

Been There, done that, Member of those....

Built for comfort not for speed angel....Well speed too !

I am a vanner, Promise me the world, give me nothing, I'll be back ... next year !


Upcoming Events
Instagram Feed
Who's Online
1 registered (jules73), 1 Guest and 6 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
cwb440, Lyle, BigBeau, owlcore, Shahadey
7924 Registered Users
Top Posters (30 Days)
Reed 111
lukester 109
Uncle_Fester 87
jules73 74
newkirkinc1 74
HighwayStar 73
frscke1 69
86ed 67
kawrider 65
Captain_E 62
Forum Stats
7924 Members
70 Forums
31008 Topics
470170 Posts

Max Online: 177 @ May 08th 2013 5:58 am

This site works best with
Download Firefox