Boxdin
Vanning.com logo
We host with and recommend Your-Site.Com - This site works best with FireFox - this site is powered by UBBCentral



Site Navigation


Advertisements
Recent Posts
Mlarky's Dodge....gonna keep her after all.
by mlarky
Natural State at the moment.
by Uncle_Fester
Just thought I'd introduce myself
by MACE
B.V.A. presents Return to Cortland July 25-27th 2014
by Suzie-BGfNY-IN
How to remove headliner??
by VanManDan345
Defrag & Disk Cleanup
by Wheelchair
09:14 AM
FORD tastic
by Callahan
08:44 AM
""Show Vans & Show Girls""
by HighwayStar
08:30 AM
How to put on a van run ?
by OVANNER
08:19 AM
Guess the 2014 Nationals attendance.
by newkirkinc1
07:20 AM
Featured Links


-->
Cluster Map
Locations of visitors to this page
Page 2 of 5 < 1 2 3 4 5 >
Topic Options
Rate This Topic
#549714 - March 19th 2012 7:26 pm Re: ABS plastic repair question [Re: mlarky]
Uncle_Fester Online   content
Festerus Vannimus

Registered: May 26th 2007 10:41 pm
Posts: 8932
Loc: On Route 66 in Bethany Oklahom...
That Q-Bond I was talking about comes with a filler powder that fills in cracks and such. . .

another video for q-bond, showing the powder usage for crack repair/ filler build up
_________________________
My vans,

1)The 1991 Dodge B250, J.Y.D.


Founder & President of Sooner or Later United Truckers and PROUD TO BE A S.L.U.T. ! !

Top
#549763 - March 19th 2012 10:37 pm Re: ABS plastic repair question [Re: mlarky]
mrmattvan Offline
addict

Registered: December 31st 2011 9:23 pm
Posts: 590
Loc: Georgia (the swamp)
I was thinking along the same lines as unclefester with my JB putty recommendation.
_________________________
94 Ford E150 4.9L inline 6 "Bad Company"

Top
#549770 - March 19th 2012 10:58 pm Re: ABS plastic repair question [Re: mlarky]
wrcsixeight Offline
veteran

Registered: April 30th 2010 8:57 pm
Posts: 1919
Loc: San Diego
JB weld is good stuff, but I don't know how it does on plastics. Perhaps fine on some but on others, not so much.

I use a lot of epoxy on my Surfboards and mix it in little graduated cups. The leftover, once cured, usually peels right out of the cup and it can be used again, where as commonly available polyester resin bonds to the same plastic cups.

I have had luck bonding plastics using crazy glue. Now since there is usually not much surface area, on the back side I like to use carbon fiber or fiberglass roving. Which is just many many strands that make up a 1/8 to 3/16 inch thick piece to saturate with crazy glue.

A bunch of these spread out along the back side of the crack to spread the stress might just do it, and not discolor the front, the way some crazy glue likes to do to plastic.

I've also known some people to melt more plastic onto the backside using a soldering iron, but I have no experience trying this.

Top
#550059 - March 21st 2012 8:39 am Re: ABS plastic repair question [Re: wrcsixeight]
mlarky Online   content
enthusiast

Registered: March 25th 2010 5:12 pm
Posts: 238
Loc: Pipe Creek Tx ( North of San A...
Not so concerned with discoloration. Plan on painting and recovering in blue to go with the denim interior I will end up with.

Top
#551340 - March 25th 2012 1:13 pm Re: ABS plastic repair question [Re: mlarky]
diamond_dave Offline
member

Registered: March 21st 2012 10:45 pm
Posts: 153
Loc: canal fulton, ohio.
i bought a plastic welder, that i use to repair all kinds of plastics on bumpers and other pieces. i use this atleast once a week at work to repair customers cars and trucks. theyre about 150 bucks. they even carry them at harbor freight, and come with lots of different plastic sticks to match all the differnt kinds of plastic parts. plus a universal filler, that works on all kinds. hope this helps.
_________________________
1969 chevy van 90

it's only the end of the world. . . . again.


Top
#551433 - March 25th 2012 8:28 pm Re: ABS plastic repair question [Re: mlarky]
mlarky Online   content
enthusiast

Registered: March 25th 2010 5:12 pm
Posts: 238
Loc: Pipe Creek Tx ( North of San A...
Thanx for the info Davetheory. I don't have $150 to spend and this is probably the only piece of plastic I have to repair. Now if you wanna come over and bring your tool...or lend it to me for a couple hours...lol. I have been doing some reading. Now I have to figure out exactly what kind of plastic this is...ABS or something else ( A chemical name I can't pronounce ) to determine how to fix it. It's getting a bit frustrating.

Top
#551672 - March 26th 2012 5:52 pm Re: ABS plastic repair question [Re: mlarky]
Uncle_Fester Online   content
Festerus Vannimus

Registered: May 26th 2007 10:41 pm
Posts: 8932
Loc: On Route 66 in Bethany Oklahom...
I told you, Q-Bond ! It cost me $30.00 for a kit with 6 bottles, and I repaired a tear in my urethane body lit a year ago and it is still holding strong. I pushed the two parts back together, put some Q-Bond drops on the front, help for 10 seconds or so so it could bond, then turned it over and added some of the powder (included in the kit) to the rear of the tear, added a few drops of Q-Bond again and let it cure about 5 mins, put the body kit back on the Astro, and have had no problems with it from then on.
_________________________
My vans,

1)The 1991 Dodge B250, J.Y.D.


Founder & President of Sooner or Later United Truckers and PROUD TO BE A S.L.U.T. ! !

Top
#551699 - March 26th 2012 8:57 pm Re: ABS plastic repair question [Re: mlarky]
mlarky Online   content
enthusiast

Registered: March 25th 2010 5:12 pm
Posts: 238
Loc: Pipe Creek Tx ( North of San A...
OK, Fester. Just need to find a place to get some near me. Will make some calls and get me a kit.

Top
#551701 - March 26th 2012 9:12 pm Re: ABS plastic repair question [Re: mlarky]
Uncle_Fester Online   content
Festerus Vannimus

Registered: May 26th 2007 10:41 pm
Posts: 8932
Loc: On Route 66 in Bethany Oklahom...
LOL It really is that good in my opinion. . . . check with most any Autobody supply shop.
_________________________
My vans,

1)The 1991 Dodge B250, J.Y.D.


Founder & President of Sooner or Later United Truckers and PROUD TO BE A S.L.U.T. ! !

Top
#552293 - March 28th 2012 9:59 pm Re: ABS plastic repair question [Re: Uncle_Fester]
mlarky Online   content
enthusiast

Registered: March 25th 2010 5:12 pm
Posts: 238
Loc: Pipe Creek Tx ( North of San A...
Ordered some thru Ebay. Should have it by the weekend. Have my fingers crossed. Wanna get the panel installed in big way.

Top
Page 2 of 5 < 1 2 3 4 5 >

Moderator:  NateNCBV 
Upcoming Events
AdSense
Instagram Feed
Who's Online
0 registered (), 4 Guests and 8 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
VanManDan345, EricS, mkycnfxt, Big_D, Rene
7861 Registered Users
Top Posters (30 Days)
lukester 99
Reed 91
HighwayStar 86
newkirkinc1 86
al55 72
jules73 71
MACE 66
Captain_E 65
kursed 62
cjhardcore 60
Forum Stats
7861 Members
70 Forums
30677 Topics
467047 Posts

Max Online: 177 @ May 08th 2013 5:58 am

This site works best with
Download Firefox